Analysis of the Physical Properties and Hardness of Teak Wood-Reinforced High-density Polyethylene and Polycarbonate Composites Produced Through Injection Moulding Technology

Rasool R. K. Al-Arkawazi; Taher Azdast; Rezgar Hasanzadeh

doi:10.51173/jt.v8i1.2814

Authors

Rasool R. K. Al-Arkawazi Department of Mechanical Engineering, Faculty of Engineering, Urmia University, Urmia, Islamic Republic of Iran
Taher Azdast Department of Mechanical Engineering, Faculty of Engineering, Urmia University, Urmia, Islamic Republic of Iran
Rezgar Hasanzadeh Department of Mechanical Engineering, Kermanshah University of Technology, Kermanshah, Islamic Republic of Iran

DOI:

https://doi.org/10.51173/jt.v8i1.2814

Keywords:

Wood Plastic Composite, Water Absorption, Swelling Thickness, Density, Hardness, Injection Molding Technology

Abstract

Environmentally friendly materials have become an important topic in practical research due to their importance to people's lives and the preservation of the environment. The use of wood plastics is of utmost importance in this field, as it is possible to obtain materials with properties that combine the strength of polymers with the properties of wood. The goal of the current study is to enhance wood-plastic composites by incorporating high-density polyethylene (HDPE), Polycarbonate (PC), and teak wood to improve their hardness and physical properties. An injection molding machine is used to prepare the samples. The Taguchi method is adopted to test the experimental design and three independent variables including teak wood particle size, weight %, and PC content. Samples are tested for water absorption, swelling thickness, density, and Shore D hardness. The findings show that an enlarged teak wood composition can result in greater water absorption and increased swelling thickness. However, the incorporation of PC added in the ratio of 7.5–15% of PC can result in better dimensional stability and decreased water absorption. Wood and PC are also added, which enhance the hardness with respect to pure polyethylene. Through Taguchi method analysis indicate that teak wood content is the most contributing factor towards these properties, followed by PC content and particle size, being least. The results also show that the model L7 type can provide the most balanced performance against mechanical and physical properties. It can be observed from the present work that the wood-plastic composites used have good mechanical properties and good moisture resistance, and are highly suitable for sustainable engineering applications.

Downloads

Download data is not yet available.

Author Biographies

Rasool R. K. Al-Arkawazi, Department of Mechanical Engineering, Faculty of Engineering, Urmia University, Urmia, Islamic Republic of Iran

Taher Azdast, Department of Mechanical Engineering, Faculty of Engineering, Urmia University, Urmia, Islamic Republic of Iran

Rezgar Hasanzadeh, Department of Mechanical Engineering, Kermanshah University of Technology, Kermanshah, Islamic Republic of Iran

References

Y. Guo, S. Zhu, Y. Chen, and D. Li, "Thermal properties of wood-plastic composites with different compositions," Materials, vol. 12, no. 6, p. 881, 2019, doi: 10.3390/ma12060881.

R. R. Al-Arkawazi, T. Azdast, and R. Hasanzadeh, "Effects of teak wood and polycarbonate additives on the tensile, flexural and impact performances of HDPE-based wood–plastic composites," International Wood Products Journal, p. 20426445251381421, 2025, doi: 10.1177/20426445251381421.

J. Zhang, A. Koubaa, D. Xing, W. Liu, H. Wang, X. Wang, and Q. Wang, "High-performance lignocellulose/polycarbonate biocomposites fabricated by in situ reaction: Structure and properties," Composites Part A: Applied Science and Manufacturing, vol. 138, p. 106068, 2020, doi: 10.1016/j.compositesa.2020.106068.

J. Zhang, A. Koubaa, D. Xing, H. Wang, F. Wang, X.-M. Wang, and Q. Wang, "Flammability, thermal stability, and mechanical properties of wood flour/polycarbonate/polyethylene bio-based composites," Industrial Crops and Products, vol. 169, p. 113638, 2021, doi: 10.1016/j.indcrop.2021.113638.

J. Zhang, A. Koubaa, D. Xing, H. Wang, Y. Tao, X.-M. Wang, and P. Li, "Fire behavior and failure model of multilayered wood flour/HDPE/polycarbonate composites with a Sandwich structure," Polymers, vol. 14, no. 14, p. 2833, 2022, doi: 10.3390/polym14142833.

Z. Mitaľová, D. Mitaľ, and K. Berladir, "A concise review of the components and properties of wood–plastic composites," Polymers, vol. 16, no. 11, p. 1556, 2024, doi: 10.3390/polym16111556 .

L. O. Vasiljevs et al., "Changes in Wood Plastic Composite Properties After Natural Weathering and Potential Microplastic Formation," Forests, vol. 15, no. 12, p. 2102, 2024, doi: 10.3390/f15122102.

I. N. Fadhil and A. R. Al-Sarraf, "Preparation and characterization of plastic wood from cellulosic residues," Ibn AL-Haitham Journal For Pure and Applied Sciences, vol. 36, no. 4, pp. 197-206, 2023, doi: 10.30526/36.4.3230.

Y. Boztoprak, "Physical, Mechanical, and Flammability Properties of Wood–Plastic Composites (WPC) Containing Beech-Wood Flour and Flame-Retardant Additives," Polymers, vol. 16, no. 20, p. 2944, 2024, doi: 10.3390/polym16202944.

W. Hassona, A. El-Kassas, and N. Zaafarani, "A new mixing technique in the production of wood plastic composites from recycled materials," International Journal of Environmental Science and Technology, vol. 22, no. 1, pp. 331-340, 2025, doi: 10.1007/s13762-024-06137-y.

L. Chen et al., "Enhancing wood-plastic composites for high-performance structural applications," Composites Part B: Engineering, vol. 299, p. 112410, 2025, doi: 10.1016/j.compositesb.2025.112410.

N. Ayrilmis et al., "Effects of Reinforcement by Both Waste Glass and Barley Straw on Water Resistance, Mechanical, and Thermal Properties of Polyethylene Composite," BioResources, vol. 20, no. 3, 2025, doi: 10.15376/biores.20.3.5967-5987.

S. K. Paramasivam et al., "Mechanical and Thermal Behavior Analysis of Chicken Feather/Sesbania grandiflora Fibers-based Hybrid Epoxy Composites," BioResources, vol. 20, no. 4, 2025, doi: 10.15376/biores.20.4.8591-8610.

P. Pandiarajan et al., "Enhancing Polyester Composites with Nano Aristida hystrix Fibers: Mechanical and Microstructural Insights," BioResources, vol. 20, no. 4, 2025, doi: 10.15376/biores.20.4.9257-9281.

D. Bachtiar et al., "Effect of alkaline treatment on the thermal and mechanical properties of sugar palm fibre reinforced thermoplastic polyurethane composites," Scientific Reports, vol. 15, no. 1, p. 14085, 2025, doi: 10.1038/s41598-025-99227-x.

R. R. Al‐Arkawazi, T. Azdast, and R. Hasanzadeh, "Investigation of the effects of walnut shell wood particles on the mechanical properties of injection molded wood‐polyethylene‐polycarbonate composites," SPE Polymers, vol. 6, no. 2, p. e10175, 2025, doi: 10.1002/pls2.10175.

I. P. Company. "HDPE – CRP100N." Iran Petrochemical Company. https://petrobon.com/product/crp-100-n/ (accessed 5 Nov. 2025).

L. C. Corporation. "LOTTE PC-1100 Technical Data Sheet", Lotte Chemical. https://www.ulprospector.com/plastics/en/datasheet/133400/lotte-pc-1100 (accessed 8 August 2025).

C. C. C. Limited. "COACE Chemical Company Limited Website." https://coacechemical.en.made-in-china.com/ (accessed 2024-05-23).

J. Chen, Y. Wang, C. Gu, J. Liu, Y. Liu, M. Li, and Y. Lu, "Enhancement of the mechanical properties of basalt fiber-wood-plastic composites via maleic anhydride grafted high-density polyethylene (MAPE) addition," Materials, vol. 6, no. 6, pp. 2483-2496, 2013, doi: 10.3390/ma6062483.

M. Mojaver, T. Azdast, and R. Hasanzadeh, "Assessments of key features and Taguchi analysis on hydrogen rich syngas production via gasification of polyethylene, polypropylene, polycarbonate and polyethylene terephthalate wastes," International Journal of Hydrogen Energy, vol. 46, no. 58, pp. 29846-29857, 2021, doi: 10.1016/j.ijhydene.2021.06.161.

R. Hasanzadeh, P. Mihankhah, T. Azdast, S. Aghaiee, and C. B. Park, "Optimization of process parameters of fused filament fabrication of polylactic acid composites reinforced by aluminum using Taguchi approach," Metals, vol. 13, no. 6, p. 1013, 2023, doi: 10.3390/met13061013.

S. H. Ameen, R. R. Al-Arkawazi, M. A. Al-Obaidi, R. A. A. Saeed, and T. B. Abbas, "Fortifying Sustainability: Enhancing the Impact Strength of Polylactic Acid (PLA) Plastic Products," Sciendo, vol. 3, p. 4, 2024, doi: 10.2478/9788368412031-005.

S. Khaleghi, T. Azdast, A. Doniavi, and R. Hasanzadeh, "Performance optimization of acrylonitrile butadiene styrene/thermoplastic polyurethane composite foams blown with carbon dioxide using Taguchi technique," Journal of Applied Polymer Science, vol. 141, no. 8, p. e54996, 2024, doi: 10.1002/app.54996.

S. Rodriguez-Fabia, J. Torstensen, L. Johansson, and K. Syverud, "Hydrophobisation of lignocellulosic materials part I: physical modification," Cellulose, vol. 29, no. 10, pp. 5375-5393, 2022, doi: doi.org/10.1007/s10570-022-04620-8.

E. Pasquier, R. Skunde, and J. Ruwoldt, "Influence of temperature and pressure during thermoforming of softwood pulp," Journal of Bioresources and Bioproducts, vol. 8, no. 4, pp. 408-420, 2023, doi: 10.1016/j.jobab.2023.10.001.

A. Delviawan, Y. Kojima, H. Kobori, S. Suzuki, K. Aoki, and S. Ogoe, "The effect of wood particle size distribution on the mechanical properties of wood–plastic composite," Journal of Wood Science, vol. 65, no. 1, p. 67, 2019, doi: 10.1186/s10086-019-1846-9.

L. Ranakoti, P. Rakesh, and B. Gangil, "Role of wood flour on physical and mechanical properties in polymer matrix composites-a critical review," Revue des Composites et des Matériaux Avancés, vol. 31, pp. 81-92, 2021, doi: 10.18280/rcma.310203.